• Donations

    If you like our website and want to give something back, you can make a donation.

    Please select a preferred amount of the donation, and then click the poster image below.

    Donation Amount

  • How to fix Wave 3, 50 and 64 gun ships.

    First cut off the forestays.


    Cut them apart and turn them around. Trim the lower edge to fit the other way.


    Make extensions for the masts by heating some plastic rod and stretching it to the desired thickness. Being an old modeler I have plastic sprues I use.


    Drill very shallow holes in the tops


    Glue extensions in place.


    Glue forestays in place. Let the inner point to the topgallant masts base.


    I will repeat the mast extension for the topmasts too one level higher up, but I think it's the fighting tops that look most strange missing the tops of the masts.
    This article was originally published in forum thread: How to fix Wave 3, 50 and 64 gun ships. started by TexaS View original post
    Comments 13 Comments
    1. Nightmoss's Avatar
      Nightmoss -
      It might be a bit easier and safer to purchase plastic rods of the correct dimension?

      Do you use a heat gun or open flame to soften the plastic? In the old days I just used a candle to stretch plastic, but in retrospect breathing melting plastic fumes was probably not a good thing?
    1. Bligh's Avatar
      Bligh -
      That takes me back a few more years than I care to admit Jim.
      What used to annoy me most was the black soot marks that got integrated with the plastic.
      I agree that with the plastic and acrylic rods so easy to get these days, and the inherent dangers from plastic fumes, or accidental burns it hardly seems worth the effort to stretch your own.
      Rob.
    1. TexaS's Avatar
      TexaS -
      I use an open flame.

      The thing with buying rods is that you have to buy a lot of dimensions to have all the ones needed. But if you have them then that would be better
    1. Bligh's Avatar
      Bligh -
      I just collect an odd one or two, each time I'm in the Hobby shop. That way it does not hurt so much.
      I do the same with sheet polystyrene.
      Rob.
    1. Nightmoss's Avatar
      Nightmoss -
      Quote Originally Posted by Bligh View Post
      That takes me back a few more years than I care to admit Jim.
      What used to annoy me most was the black soot marks that got integrated with the plastic.
      I agree that with the plastic and acrylic rods so easy to get these days, and the inherent dangers from plastic fumes, or accidental burns it hardly seems worth the effort to stretch your own.
      Rob.
      Oh boy that does take me back. I used to do that to make the wire aerials for my model battleships, etc. The soot flew everywhere (and probably right into my lungs).

      Quote Originally Posted by TexaS View Post
      I use an open flame.

      The thing with buying rods is that you have to buy a lot of dimensions to have all the ones needed. But if you have them then that would be better
      I know exactly what you mean. I often find the size I want is always sold out too. Keep the room well ventilated then in any case.

      Quote Originally Posted by Bligh View Post
      I just collect an odd one or two, each time I'm in the Hobby shop. That way it does not hurt so much.
      I do the same with sheet polystyrene.
      Rob.
      That's almost exactly how I do it Rob.
    1. TexaS's Avatar
      TexaS -
      I have adequate ventilation and I make sure to not burn the plastic and as you can see I don't get any soot in my plastic.
    1. Bligh's Avatar
      Bligh -
      No Jonas you certainly don't. Your superb pristine painted models are a testimony to that.
      Also how clean you keep the front of your uniform!
      Have you any other useful tips about the use of plastic sprue or such?
      Rob.
    1. TexaS's Avatar
      TexaS -
      I use... nightlights?



      I keep the plastic quite high above the flame and rotate it. It's slower but I have better control.

      About the uniform... Modern stain removers work wonders on port stains as well as strawberry... Usually just the shirt that's been affected.

      By the way, Rob... It you're making a uniform too, I can tell you that I use silk thread to sew on the gold band. Those are metal and therefor cut the thread when used. I have recently repaired a lot of the stitches. I usually wait until longer stretches need restitching.
    1. Bligh's Avatar
      Bligh -
      Thanks Jonas, I will pass that advice about stitching on to my good lady.
      Rob.
    1. TexaS's Avatar
      TexaS -
      It might not be advice but rather information.

      I used silk thread since it's historical and shiny but if you use some modern synthetic it might be stronger.
    1. Bligh's Avatar
      Bligh -
      No modern synthetics were it shows is the watchword.
      Rob.
    1. TexaS's Avatar
      TexaS -
      I understand that. I went with only historical threads and hand stitched where it shows.

      There are many choices for lining though. Linen, cotton, silk or combinations are all historical. I went with linen. I also went fully lined which apparently was unusual. The back (waist up) was often not lined.
    1. Bligh's Avatar
      Bligh -
      I think fully lined is a sound idea Jonas.
      The linen option also appeals because it wears well and won't show perspiration marks like silk does.
      Also laundering is made easier with a Wool coat lined with linen as long as you remembered to pre wash the Linen before making up the coat.
      Rob.
  • Recent Posts

    Diamondback

    What's on your workbench for October?

    Suggestion for statting 1810 Essex: I'd propose a two-track approach if David Manley has time to assist. Option A would be apply the regular Ares carronade

    Diamondback Today, 16:12 Go to last post
    Bligh

    What's on your workbench for October?

    For those interested in more information on the USS Essex see here:- https://sailsofglory.org/showthread....5752#post95752

    Bligh Today, 14:21 Go to last post
    Bligh

    USS Essex.

    Here is a special to thank my American friends for all the support and advice given to me during my project in building up my American Naval squadron.

    Bligh Today, 14:18 Go to last post
    McDorf

    What's on your workbench for October?

    Those are some gloriously beautiful bases!

    Duncan has given me a wee project - https://www.youtube.com/watch?v=eKg8oPF4xfk
    My next

    McDorf Today, 12:12 Go to last post
    Bligh

    Third Rate 64 gun ships of the Royal Navy.

    This concludes my list of 64 gun ships of the line, 1793 to 1815. I will next deal with the Fourth Rate 60 and 50 gun ships launched during the

    Bligh Today, 10:26 Go to last post
    Bligh

    What's on your workbench for October?

    And this concludes my USS Essex cards.

    Bligh Today, 10:13 Go to last post
    Bligh

    What's on your workbench for October?

    Good to hear from you Julián and thanks for all the eye candy. It was just what we needed to lift the spirits here on a very dull chilley and stormy day.

    Bligh Today, 10:07 Go to last post
    Redcoat

    What's on your workbench for October?

    Hello mates! I have not posted here for a long time, the truth is that I have been quite busy with various projects and personal issues that do not transcend

    Redcoat Today, 08:13 Go to last post
    Bligh

    Favourite Nautical related tipple.

    ...

    Bligh Today, 04:28 Go to last post
    Bligh

    Nautical related Taverns.

    Old Royal Ship Inn. Luckington.

    Bligh Today, 04:24 Go to last post
    Bligh

    What's on your workbench for October?

    Thanks Dave.
    I hope to have them in action in a few days time.
    Rob.

    Bligh Yesterday, 16:42 Go to last post
    Bligh

    Third Rate 64 gun ships of the Royal Navy.

    HMS Lancaster (1797)

    HMS Lancaster was a 64 gun third rate ship of the line built by Randall & Co. at Rotherhithe. Launched on 29th of

    Bligh Yesterday, 14:51 Go to last post
    David Manley

    What's on your workbench for October?

    They do make a fine pair

    David Manley Yesterday, 12:58 Go to last post
    Bligh

    What's on your workbench for October?

    Even more eye candy DB, and here is my completed Essex herself.
    Just done the US Flag decal. Just the ship card to go now.
    Rob.

    Bligh Yesterday, 11:21 Go to last post
    Diamondback

    What's on your workbench for October?

    [QUOTE=Bligh;95731]

    Miller actually did a series that I'd like to know more about... the other three were Voyage, Storm and Harbor Sunrise.

    Diamondback Yesterday, 10:39 Go to last post
    Bligh

    What's on your workbench for October?

    Ship base mat for Essex now done.

    Bligh Yesterday, 10:29 Go to last post
    Bligh

    Nautical related Taverns.

    Riverway.

    Bligh Yesterday, 02:20 Go to last post
    Bligh

    Favourite Nautical related tipple.

    ...

    Bligh Yesterday, 02:17 Go to last post
    Bligh

    What's on your workbench for October?

    Maybe something like this Dave.

    Rob.

    Bligh Yesterday, 02:11 Go to last post
    Bligh

    What's on your workbench for October?

    I'm just glad to hear you are not Sneezy Dave. We don't have an enoticon with a Covid mask. Needs rectifying, and Tim does not venture here as you

    Bligh Yesterday, 01:54 Go to last post