PDA

View Full Version : Building and painting the HMS Sovereign



fire6
12-05-2011, 20:54
I've chosen the Langton Miniatures ships and I've selected the 1st rate HMS Royal Sovereign as the example. I'll be naturally stating with assembly followed painting, rigging, base work and finally transport / storage.

This is the contents of a Langton British starter set. They normally sell them as separate parts, you pick the hull, sail set then resin base and rat lines. The set has 4 hulls with "easy"sail sets, photo etch rat lines, bases and a ensign set.

http://sailsofglory.org/attachment.php?attachmentid=229&d=1323121970

These are the tools needed to assemble them. A Xacto knife, small needle files, super glue and a pin vice with a assortment of bits. The small stack to the left are tiny rare earth magnets.

http://sailsofglory.org/attachment.php?attachmentid=234&d=1323121974


Hull

Using the knife and files clean the small amount of flash and mold lines. I start with the hull and stern peice saving the sails for later. After cleaning the cast I wash them in warm water with a small amount of dish soap.

http://sailsofglory.org/attachment.php?attachmentid=228&d=1323121970

Hull and Stern

http://sailsofglory.org/attachment.php?attachmentid=227&d=1323121969

After drying I drill out the three mast and Bowsprit points. They are already there but rather shallow and small for a good fit.

http://sailsofglory.org/attachment.php?attachmentid=233&d=1323121974

Next I mount the Hull to the resin base. Note Ive reconsidered this step and will in future mount the Hull temporally to a Popsicle stick for easier painting. For the base I drill 3 1/8 holes to receive the magnets.

http://sailsofglory.org/attachment.php?attachmentid=288&d=1323122041

While it may be possible to carefully drill and recces the magnets the final base work will cover them so I drill through and

http://sailsofglory.org/attachment.php?attachmentid=226&d=1323121969

Insert them and setting them to the bottom of the base and gluing in place.

http://sailsofglory.org/attachment.php?attachmentid=225&d=1323121968

http://sailsofglory.org/attachment.php?attachmentid=223&d=1323121966

Next glue the Hull to the base and set aside. Now its time to get the sail set out. This is a 3 deck Easy sail set with the Mizzen, Main, Fore masts and Bowsprit.

http://sailsofglory.org/attachment.php?attachmentid=224&d=1323121967

I've chosen the white metal set as the Photo etch may be a bit fiddly for gaming!

http://sailsofglory.org/attachment.php?attachmentid=232&d=1323121973

Next I drill out all of the holes needed for rigging. This is .20 bit.

http://sailsofglory.org/attachment.php?attachmentid=231&d=1323121972

I drill just above the fighting tops of each mast and the Bowsprit just under the jib sail.

http://sailsofglory.org/attachment.php?attachmentid=222&d=1323121965

Next I drill out the Hull. For the masts drill a hole at the rear of each channel (ledges along the hull where the ratlines attach) that's 6. Then 1 just bellow the Figurehead at the bow. The final ones are in the cathead's if possible or through the bulkhead's just behind them if not.

http://sailsofglory.org/attachment.php?attachmentid=221&d=1323121964

That's it with Hull now its time for the sails.


Sails

http://sailsofglory.org/attachment.php?attachmentid=219&d=1323121962

I use small blocks of wood hold the masts for painting. You'll want to lay them out as they will be assembled to prevent any mistakes. The Mizzen is easy to figure out but the Main and Fore masts are very similar. After that's done I use a needle file to put a small grove in each sail set this helps the gluing.

http://sailsofglory.org/attachment.php?attachmentid=220&d=1323121962

http://sailsofglory.org/attachment.php?attachmentid=230&d=1323121971


This done insert the Bowsprit and attach its yard. Then attach the sails and yards to the masts. You should angle the Sail/yard pieces slightly to the right side.
Every thing ready for priming.

http://sailsofglory.org/attachment.php?attachmentid=218&d=1323121961

Painting the Hull

I've used Rust-olium auto primer for some time now, it has a very fine coat, forgiving the times I lay on to much. It also shrinks up nicely. The light gray is a good compromise between black that obscures details and white that can be hard to cover.

http://sailsofglory.org/attachment.php?attachmentid=217&d=1323121960

Guides: I've used these as well as bad ole internet. The Langton booklet is a great resource, I highly recommend it to any interested ship builders. Age of Sail is also very useful.

http://sailsofglory.org/attachment.php?attachmentid=241&d=1323121980

Tools: While I prefer the Windsor Newton Series 7 miniature brushes I'm by no means a brush snob. Most brushes if well cared for will give good service all of my utility brushes are craft shop sets. I use a #2 for large areas a #1 for the 1st go through and a 00 or 000 for clean up and detail work.
About cleaning the water well is for quick cleaning or wetting the brush and the jar with the coil has a good brush cleaner for use between colors and final clean up. You will note the 2 desk lamps in the photo, what you don't see are the 4 fixtures above the desk 2 florescent tube and 2 40w = 100w spirals. I like lots of light and I'm always surprised how much better things look after I clean my glasses!

http://sailsofglory.org/attachment.php?attachmentid=261&d=1323122001

http://sailsofglory.org/attachment.php?attachmentid=255&d=1323121995

One of my favorite tools. This hand vise has been great help you not only need a steady brush you also need a steady mini!

http://sailsofglory.org/attachment.php?attachmentid=239&d=1323121979

Paints: Mostly Vallejo Game and Model colors. I've found the Coat d"arms cover very well and use their black & white. Then its a mix of GW, P3 and whatever else catches my eye. I will list what's been used for this ship as we go along.

http://sailsofglory.org/attachment.php?attachmentid=256&d=1323121996

First up the Hull

http://sailsofglory.org/attachment.php?attachmentid=240&d=1323121979

I prime white the side that is to be painted yellow.

http://sailsofglory.org/attachment.php?attachmentid=257&d=1323121996

Now the spaces between the Wales with the closed gun ports get a coat of Vallejo Gold Yellow. A note here don't get to hung up on the colors this is the late 1700's early 1800's paint is going to be very inconsistent. Not only in shade but supply, also some of these ships had very long carers at times with multiple navy's!


http://sailsofglory.org/attachment.php?attachmentid=242&d=1323121981

Next is the tricky part. Take your time and keep er steady, small brush (0 or 00) a little paint and small sections at a time. Trying to do a entire Wale from stem to stern in one go is tough. Keep it simple. I've painted the Bowsprit as well as it and the Masts are to be the same color.

http://sailsofglory.org/attachment.php?attachmentid=258&d=1323121997

That's it for the Hull sides. Up next is the Bulkheads and Decks. I start with the inner Bulkheads. For the RS its P3 Sckorne Red but any dark red will do. Then the Deck for this its Bone white. The Hammock netting is white and will get a wash later.

http://sailsofglory.org/attachment.php?attachmentid=243&d=1323121983

The gun carriages are Vallejo Scrofulous brown as are the other Deck rails, stairs and grates. The guns are black with a dark gray highlight.

http://sailsofglory.org/attachment.php?attachmentid=245&d=1323121985

As you can see in these photos I've also primed the Stern and Head rails.

http://sailsofglory.org/attachment.php?attachmentid=259&d=1323121998

http://sailsofglory.org/attachment.php?attachmentid=260&d=1323122000

Now the Stern galleys again primed white for the yellow and a dark blue for the windows.

http://sailsofglory.org/attachment.php?attachmentid=244&d=1323121984

http://sailsofglory.org/attachment.php?attachmentid=235&d=1323121975

The Bow.

http://sailsofglory.org/attachment.php?attachmentid=251&d=1323121991

With this done I next put down a light brown wash on the deck and a light black on the Hammock netting.

http://sailsofglory.org/attachment.php?attachmentid=248&d=1323121988

http://sailsofglory.org/attachment.php?attachmentid=246&d=1323121986

And

http://sailsofglory.org/attachment.php?attachmentid=247&d=1323121986

Painting the Masts and Sails.

I start with a Vallejo Bone White base painting the sail first.


http://sailsofglory.org/attachment.php?attachmentid=262&d=1323122002

Next its a white dry brush.

http://sailsofglory.org/attachment.php?attachmentid=238&d=1323121977


After that I pick out the Buntline and Reef point lines with Ocher Green. I use this on the tie off points on the yards as well.

http://sailsofglory.org/attachment.php?attachmentid=252&d=1323121992

http://sailsofglory.org/attachment.php?attachmentid=253&d=1323121992

If you've the time and patience you could add patches and seams adds a nice touch.

http://sailsofglory.org/attachment.php?attachmentid=236&d=1323121976

Ok on to the masts. For the Royal Sovereign I've painted the lower and mid section Gold Yellow.

http://sailsofglory.org/attachment.php?attachmentid=254&d=1323121993

The top section and yards are Vallejo Scrofulous brown to simulate varnished wood. The Fighting tops are black.

http://sailsofglory.org/attachment.php?attachmentid=253&d=1323121992

With that done I seal the hull and sails with this, works as well as dull coat at a lower cost.

http://sailsofglory.org/attachment.php?attachmentid=237&d=1323121976

Setting the sails to the Hull. With a small amount of super glue (to much will squirt out on to your nice clean deck). The foremast should be canted slightly forward. The mainmast and mizzenmast slightly abaft. Don't worry about how they drop in initially after the glue sets you can go back and carefully bend the into position. Also take a look forward from the stern getting the tops lined up.

Scale check

http://sailsofglory.org/attachment.php?attachmentid=249&d=1323121989

http://sailsofglory.org/attachment.php?attachmentid=263&d=1323122002

http://sailsofglory.org/attachment.php?attachmentid=250&d=1323121990



Rigging

Its not that difficult honest. Like anything else with the right tools and patience it can be done. Your ship will look unfinished without it.

http://sailsofglory.org/attachment.php?attachmentid=274&d=1323122021

The stand is some scrap lumber with a clamp and a hole for my hand vice. The stand helps in two ways first it raises the ship to eye level, second it allow you to spin the ship with ease for rigging from port to starboard.

http://sailsofglory.org/attachment.php?attachmentid=275&d=1323122022

The other items are a xacto with a fresh blades to cut thread ends. Two tweezers to tie the smaller knots ( you might notice that I've one squeeze to grip type and a squeeze to release type, my brain had a real hard time with this! ). Super glue to set the knots with tooth picks to apply it. And naturally the thread I have a single strand polyester and a .8mm (.003") thread. The polyester looks better as its closer to scale but its very fiddly with a natural spring to it. The .8mm thread is what I'll be using this time.

http://sailsofglory.org/attachment.php?attachmentid=267&d=1323122008

Remember the holes I drilled during the assembly stage? This is why. What I'll be doing here is the Standing rigging these are the lines that hold the masts in place as apposed to the Running rigging that is used to work the sails. The Standing Rigging will keep you mini's masts in place fore and aft, larboard to starboard imagine that : ) Staring with the Foremast tie one end off on the Channel or Bulkhead depending on where drilled, give it a bit of glue. Now run this up through the upper Fighting top and and down to the channel on the other side tie this off and run it up to a point above the upper fighting top. I dont tie them off here only at the sides. After securing it at the channel you started with run it up to the top of the mast. Tie it at this point and run it down finishing off at the opposite channel. This will give you three lines spaced up the mast holding the mast firmly side to side, you'll also note that as the hull points were drilled slightly aft of the masts they are held firmly aft. Repeat on the other two masts.

http://sailsofglory.org/attachment.php?attachmentid=276&d=1323122023

http://sailsofglory.org/attachment.php?attachmentid=268&d=1323122009

Next up is the fore aft rigging. This can be a complex or simple as you like. I start at the lower sections first. From the lower fighting top of the mizzen mast I run a line to the base of the main mast. Then a line from the upper fighting top of the mizzenmast through a hole in the mainmast to the base of the foremast. The third line is from the top yard of the mizzenmast through the hold at the upper fighting top of the mainmast then to the lower fighting top of the foremast from there I tie off at the hole above the yard on the bowsprit, from the bowsprit one last line to the hold on the hull just below the figurehead. The point of this whole mess is you now have a good deal of strength from the lines tied to the hull behind the mizzenmast through each mast and the bowsprit and back to the hull.

http://sailsofglory.org/attachment.php?attachmentid=273&d=1323122020

After that I run three more for aft lines. Note the one line that was specifically run with a eye to match the angle of the jib sail. Also note the line placed on the rear or mizzen sail this will be used to attach the ensign.

http://sailsofglory.org/attachment.php?attachmentid=279&d=1323122029

Now on to the bowsprit. This line starts at a hole in the bulkhead just behind the cathead from here to the yard tie here, at the tip of the bowsprit and on to the other end of the yard. Next to the opposite bulkhead. Not done yet now run the line through the hole in the bowsprit above the yard and back to your start point and secure it.

http://sailsofglory.org/attachment.php?attachmentid=278&d=1323122027

http://sailsofglory.org/attachment.php?attachmentid=277&d=1323122026

For a better idea of what I'm trying to get across here there is Langton Miniatures' Assembly, Painting & Rigging of Napoleonic Naval Models in Scale 1:1200 long title excellent resource.

Three more steps Rat lines, Basing and Transport.

The Langton photo etch ratlines are easy to use and add another nice touch of realism. The three deck set has 4 lines per mast while their not numbered you can tell what goes where.

http://sailsofglory.org/attachment.php?attachmentid=272&d=1323122018

I prime them and paint them on the sprue adding a spot of brown for the eye's

http://sailsofglory.org/attachment.php?attachmentid=266&d=1323122007

Cut them out with a small sharp pair of scissors. Fit check each one before applying a small amount of superglue and setting them. The lower one should set on the channel and should attach just under the fighting top. The next one sets on the lower fighting top and fits under the upper fighting top. Fit testing is vital a misapplication of superglue at this scale is bad, very bad trust me.

http://sailsofglory.org/attachment.php?attachmentid=265&d=1323122006

http://sailsofglory.org/attachment.php?attachmentid=287&d=1323122040

After the ratline its the ensign and pennants these came with the 4 hull sets but like the ratlines can be purchased separately.

http://sailsofglory.org/attachment.php?attachmentid=264&d=1323122006

Base:
Originally I had set three small rare earth magnets in the resin base provided. During painting I found that while this looked best the base was to low or thin and risked damaging the ship each time you picked it up. To remedy this I added a Litko 3mm x 40mm x 80mm plywood riser.
The extra 5mm length gives me a place to add a magnetic name plate and the 3mm rise makes it easy to pick up. Oh yes I did add three of the small rare earth magnets to the new bottom.

http://sailsofglory.org/attachment.php?attachmentid=280&d=1323122030


The base color is Vallejo Scurf Green followed with a dry brush of Wolf Gray and topped with a light dusting of White. To give it the translucent wet look I topped it all with a layer of Vallejo Water effects well, "Transparent Water".

The transport case is a $9 pine case from a craft shop. I removed the handle and flipped it over putting a new handle on the "bottom". Then a block of 3/4 pine was added to the inverted bottom to make it flush. To this a thin sheet of steel was added for the base magnets. This gives me a hard case that I don't have to risk the masts and yards to get the ship out of. Why all of the added trouble? unlike other mini's damaging one of these ships is likely to be the end of it.

http://sailsofglory.org/attachment.php?attachmentid=284&d=1323122035

http://sailsofglory.org/attachment.php?attachmentid=283&d=1323122034


http://sailsofglory.org/attachment.php?attachmentid=286&d=1323122039

http://sailsofglory.org/attachment.php?attachmentid=285&d=1323122038


The finished item HMS Royal Sovereign. Thanks again for taking a look hope it helps.

http://sailsofglory.org/attachment.php?attachmentid=270&d=1323122016

http://sailsofglory.org/attachment.php?attachmentid=271&d=1323122017

http://sailsofglory.org/attachment.php?attachmentid=282&d=1323122034

http://sailsofglory.org/attachment.php?attachmentid=281&d=1323122032

http://sailsofglory.org/attachment.php?attachmentid=269&d=1323122016

Bligh
12-06-2011, 03:11
That is magnificent Wayne. Both the explaination and the finished model beggars belief.
Rob.

Old Salt
12-06-2011, 04:48
That is super , I think I need to redo all of mine. But I won't come close to that.

Berthier
12-06-2011, 04:52
No pictures coming up when I view the post..I'm sure they are great but it would be nice to see them ; )

The Royal Hajj
12-06-2011, 05:17
Are they showing up now?

Berthier
12-06-2011, 05:40
Can see pictures now and they are sensational. This is a real masterclass in building well done!

mt1ss bob
12-06-2011, 06:40
WOW AMAZING I have done 3 of these models and after seeing this I want to sink mine
bob

Skullduggery
12-06-2011, 06:55
Very nice work

Horatio Nelson
12-06-2011, 06:56
Superb job Wayne. Does you proud.

Gaz67
12-06-2011, 09:57
Really, Really nice work there, I'm SO glad that I'll be able to buy pre-paints!!

Comte de Brueys
12-06-2011, 10:10
No comment!

:eek::eek::eek:

...brilliant.

Horatio
12-06-2011, 10:29
She's a beut.
A real work of art.:)

Attila57
12-06-2011, 12:26
Your skill is breathtaking.

Attilio

The Cowman
12-06-2011, 12:41
Some of the best small scale modelling I have ever seen!

Anav
12-06-2011, 15:15
WOW (Mouth open)

Capt P
12-06-2011, 16:37
This is an awsome set of pics. You have done a great job and I wish I do half as good.

Tommy Z
12-06-2011, 16:48
Outstanding work & a very helpful tutorial!

fire6
12-06-2011, 16:55
Thanks for all of the complements, I did this last year then hopped to other projects. Your kind coments have inspired me jump back in. That and a promise to host a game at Huzzah! May next year.:eek:

Wayne

Bluedevil
12-07-2011, 07:20
Wayne,this is one of the most complete "how to's" I've ever had the privilege to read! Nicely documented with great pictures! Thanks for sharing this...I'm sure it will come in handy!

Blackrose
12-07-2011, 15:33
Excellent how-to, esp. for those of us who have never built rigged ships at this, or any scale.
Thanks muchly. This one's going into the files for reference.
karl

The Royal Hajj
12-08-2011, 00:34
Wayne, you mention that you use .8mm thread for the rigging. Is is any kind of special thread and does it have a weight number on it? Seems most of the threads are labled by weight and not diameter.

Gunner
12-08-2011, 01:47
This is by far the best step by step tutorial on 1/1200 ships I have ever seen.
This thread will be my ship building Bible.
Thank you Wayne.

fire6
12-08-2011, 15:38
Wayne, you mention that you use .8mm thread for the rigging. Is is any kind of special thread and does it have a weight number on it? Seems most of the threads are labled by weight and not diameter.

Your right its label is W 6\0 UNI-Thread. UNI Products Inc. Its a fly-tying thread and waxed.

http://www.cabelas.com/thread-beads-eyes-uni-thread-6-1.shtml?WT.tsrc=CSE&WT.mc_id=GoogleBaseUSA&WT.z_mc_id1=743792&rid=40&mr:trackingCode=3B869052-F5D2-DF11-82EF-001B21631C34&mr:referralID=NA

VonHinnebusch
12-08-2011, 17:19
Absolutely beautiful.

fire6
12-09-2011, 15:41
Here is the rest of the fleet.

HMS Naiad 38, Polyphemus 64, Colossus 74, Mars 74, Tonnant 80, Agamemnon 64 and Temeraire 98

http://farm8.staticflickr.com/7148/6483798289_1f55ae6189_b.jpg

The French awaiting masts.

Bucentaure 80, Formidable 80, Heros 74 and Redoutable 74

http://farm8.staticflickr.com/7011/6483804691_2871593df7_b.jpg

The Spaniards up for rigging

Bahama 74 with the Santa Anna 112 to port. The two fuzzy ships are the Montanez 74 and San Leandro 64.


http://farm8.staticflickr.com/7031/6483792059_82150d94ea_b.jpg


Last but not least GHQ's USS Consttution and Langton's HMS Royal Sovereign. Note this far closer than any sane Frigate Captain would want to get to enemy ship of the line!

http://farm8.staticflickr.com/7167/6483787531_735f78d593_b.jpg

Gunner
12-09-2011, 16:31
What beauties.

If you're going to use these to play SGN, I would suggest not permanently basing them untill we see the SGN basing system.
Clear plastic? Hopefully the Royal Hajj will soon come out with bases.

fire6
12-09-2011, 19:27
What beauties.

If you're going to use these to play SGN, I would suggest not permanently basing them untill we see the SGN basing system.
Clear plastic? Hopefully the Royal Hajj willsoon come out with bases.

Good point. Theses were put together for "Trafalger" and to honest the large bases are for protection no part of the ship is safe to touch.

The Royal Hajj
12-09-2011, 23:01
More wonderful looking ships! What are the bolts for in your "Sail Wood"? Are you clamping the mast between two blocks of wood to hold them while you paint?

Bligh
12-10-2011, 01:47
I can forsee a lot of hours in the workshop in front of me! What an inspiration for building a fleet these beauties are.
Rob.

Berthier
12-10-2011, 03:03
Magnificent fleet.

It will be interesting to see how Ares manages to produced finished models for gaming. There is so much more detail that could be incorporated into a SOL compared to an aircraft, the surfaces are trickier to work with, the painting more complex, the rigging another factor.

Ive decided not to build any ships yet as I want to see the game system, basing and style of the minis first. Besides I have so many planes waiting my attention!

fire6
12-10-2011, 07:20
More wonderful looking ships! What are the bolts for in your "Sail Wood"? Are you clamping the mast between two blocks of wood to hold them while you paint?

I use two thin strips of pine held together with 6/32 bolts, washers and wing nuts. I cut a small notch in three spots to clamp the masts in place. Its much more secure than the single blocks and all three can be painted together.

The Royal Hajj
12-10-2011, 07:29
That's what I thought you were doing, but thanks for the details.

Gunner
12-10-2011, 17:52
Magnificent fleet.
Besides I have so many planes waiting my attention!

Planes? Planes? What pray tell is a plane? One of Da Vinci's contraptions? It'll never get off the ground.

Bligh
12-11-2011, 00:54
Planes? Planes? What pray tell is a plane? One of Da Vinci's contraptions? It'll never get off the ground.
Tis a tool the Master Shipwright uses to smooth timbers and spars, my old shipmate.
Bligh.

Berthier
12-11-2011, 01:11
Ah Bligh you are a card :);)

Bumblie3
12-11-2011, 12:23
Absolutely brilliant, Wayne.
John.

Capn Duff
12-12-2011, 04:57
Just plain superb, I am in envy

mt1ss bob
03-10-2012, 20:40
where did you get a guide for the colors of this ship and do you have a guide for others?

Berthier
03-12-2012, 00:59
Robert
Check out the links section here for "lots" of useful websites for ship information including colours etc

http://sailsofglory.org/showthread.php?26-Best-Research-and-Hobby-Links

fire6
03-13-2012, 15:13
where did you get a guide for the colors of this ship and do you have a guide for others?


I used Langtons Guide,Naval Warfare in the Age of Sail by Bernard Ireland and the internet.

Wayne

rrrreubanks
03-13-2012, 20:21
Wayne, I can't say anything better that hasn't already been said...beautiful job on the RS! I learned a few things myself from looking at this!
Rob

Capt P
03-27-2012, 14:57
Just saw the rest of your photos. That is outstanding work. Can't give you enoght complements on the work you have done.